The FLASH key on most analog handsets works with call waitingīuddy Watch and Presence features are not supported. Most analog handsets with Caller ID displays work, but this is not guaranteed as Fuze does not have control over how Caller ID passes through various carriers and whether that information can be properly translated from analog to digital and back to analog. Using hold feature key if available or hook switch/flash key. It is, however, possible to set up custom extensions through the Portal. Speed dials directly on handsets do not work. An analog telephone adapter (ATA) turns any standard analog phone into a device capable of completing calls in a Voice Over IP (VoIP) network. This feature is not affected by using an ATA. FeatureĬonference bridges can be dialed and used as normal. Supported features with an asterisk (*) have work-arounds available for Poly handsets. The following table provides a breakdown of supported and unsupported features. YOU HEREBY WAIVE ANY AND ALL SUCH CLAIMS OR CAUSES OF ACTION ARISING FROM OR RELATING TO YOUR INABILITY TO USE THE HT812 TO CONTACT EMERGENCY SERVICES, AND YOUR FAILURE TO MAKE ADDITIONAL ARRANGEMENTS TO ACCESS EMERGENCY SERVICES IN ACCORDANCE WITH THE IMMEDIATELY PRECEDING PARAGRAPH.If you are using a standard analog handset that is connected to an Analog Telephone Adapter (ATA) or VoIP to Analog Gateway, you can access a variety of common features. NEITHER GRANDSTREAM NOR ITS OFFICERS, EMPLOYEES OR AFFILIATES MAY BE HELD LIABLE FOR ANY CLAIM, DAMAGE, OR LOSS. GRANDSTREAM DOES NOT PROVIDE CONNECTIONS TO EMERGENCY SERVICES VIA THE HT812. If you do not do so, it is your responsibility to purchase traditional wireless or landline telephone services to access Emergency Services. It is your responsibility to purchase SIP-compliant Internet telephone service, properly configure the HT812 to use that service, and periodically test your configuration to confirm that it works as you expect. You must make additional arrangements to access Emergency Services. The HT812 is not pre-configured to support or make emergency calls to any type of hospital, law enforcement agency, medical care unit (“Emergency Service(s)”) or any other kind of Emergency Service. You may check your HT812 IP address using the IVR on the connected phone.Įnter the HT812’s IP address in the address bar of the browser.Įnter the administrator’s password to access the Web Configuration Menu. You will need to design and build some external circuitry to convert between telephone line audio (which apparently runs at 48 volts) and audio signals which the Pi can produce. Press 02 and the current IP address will be announced.Ĭonnect the computer to the same network as your HT812 and make sure the HT812 is booted up. This is probably possible, but not with the Pi alone. An analog device, such as an analog telephone or fax machine. Press *** (press the star key three times) to access the IVR menu and wait until you hear “Enter the menu option “. The Analog Telephone Adapter (ATA) allows you to connect an analog telephone card to your computer. Use a telephone connected to phone 1 or phone 2 ports of your HT812. Please refer to the steps bellow to access the interactive voice response menu: In order to know which IP address is assigned to your HT812, you should access to the “Interactive Voice Response Menu” of your adapter via the connected phone and check its IP address mode. The HT812 is by default configured to obtain the IP address from DHCP server where the unit is located. The HT812 can be configured either using the embedded Web GUI using PC’s web browser or using the IVR voice prompt menu. The Power, Ethernet, and Phone LEDs will be solidly lit when the Phone Adapter is ready for use. Insert the power adapter into the HT812 and connect it to a wall outlet. Insert the ethernet cable into the internet or LAN port of the HT812 and connect the other end of the ethernet cable to an uplink port (a router or a modem, etc.) Insert a standard RJ11 telephone cable into the phone port and connect the other end of the telephone cable to a standard touch-tone analog telephone. Grandstream GS-HT802 2 Port Analog Telephone Adapter VoIP Phone & Device, Black. The HT812 isdesigned for easy configuration and easy installation, to connect your HT812, please follow the steps above: Cisco UC 2 Port Analog Telephone Adapter ATA190 (Renewed) 1. Press for 7 seconds to reset factory default settings. Used to connect HT812 to your router or gateway using an Ethernet RJ45 cable.įXS ports to connect analog phones / fax machines to HT812 using RJ11 telephone cable.įactory reset button. Used to connect your HT812 to local network when using as router.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |